Dears,
This post is about Vaquero, and I must start with my dear LST. My Lobo ST is running in "adjusted" mode now, I did play a bit with trimmer R33 (and K10 - only touch), and results are, after couple comparing test:
1. Frequency probably move, cause other LOBO ST with the same 10x12 HOT had no disturbed it the same style as before. In distance 3-4 meters - no any didggg rhriigg in headphones, only nothing, any signal. Fantastic, but it is dangerous for club trips.
2. LST in disc mode in sens pure 10 and disc 2 and threshold 80-90% is going deeper than before (I cannot index other machines here, it is clear). Running over machines as have been never before.
3. In my standard former settings - Sens in red but no in max, Thresh in max, disc 1 and half and some - it is first time unstable, now. I can heard coil moving! Great! If is targeted good metal, disturb noise is quite and you can heard "standard" LST goose noise - clean and straight.
4. In this setting - adjusted - is better going in normal and for pinpointing switch to Black sand mode and it is OK.
5. GB for disc is I suppose at this moment negative, nice negative.
My main interest is: DO YOU HAVE ANY info which trimmer is important for change factory preset mode from permanent POS (in disk mode) to NEG mode? I am looking for picture of control board and indexing right trimmer. It can be the same for all Freq?
So, do not hesitate support this discussion, and if we will have lucky, I will posted back result, be sure.
The best way how to explain it is asking WHY, you know.
Why I want to do it?
1. AD 180 can do more.
2. Too positive GB is good for disk stability, but reducing depth for small targets in disk mode.
3. I need any disk for iron as minimum only, disk circuit is very good, survive it and me too.
4. I need hear detector "tick tig ticky tig" - light noise during swimming - it is significant mark - this is a maximum of power, maximum of volume what I can get.
5. Better in depth is the same as better in small targets, is not it.
6. So, result what I called is raise a chance catch specific unclear noises small targets what are deeper than standard (POS/NEUTRAL/NEG- in acceptable level) set up Vaquero can do.
7. My experience is, if I use overloaded receiver and AD 180 (f.e. unstable set Tejon), no problem with AD 180. Tick tig ticky stopped and indexing beep is clear, strong and good.
8. Factory preset Vaquero is stable too much. It sitting down too conservative. I have no chance to do it what I want through negative AM GB only, at this moment it is wrong, to be too much negative in AM, due lost small targets, it is non-productive way.
Result is: I need light shift with Disk GB to NEG. It is all.
Reason is: I need IT.
Ufff, thank you, it was useful for me for fixing my thoughts and describing it, thanks again, .... schematic? Which trimmer need to be adjusted?
Regards
litrfree
This post is about Vaquero, and I must start with my dear LST. My Lobo ST is running in "adjusted" mode now, I did play a bit with trimmer R33 (and K10 - only touch), and results are, after couple comparing test:
1. Frequency probably move, cause other LOBO ST with the same 10x12 HOT had no disturbed it the same style as before. In distance 3-4 meters - no any didggg rhriigg in headphones, only nothing, any signal. Fantastic, but it is dangerous for club trips.
2. LST in disc mode in sens pure 10 and disc 2 and threshold 80-90% is going deeper than before (I cannot index other machines here, it is clear). Running over machines as have been never before.
3. In my standard former settings - Sens in red but no in max, Thresh in max, disc 1 and half and some - it is first time unstable, now. I can heard coil moving! Great! If is targeted good metal, disturb noise is quite and you can heard "standard" LST goose noise - clean and straight.
4. In this setting - adjusted - is better going in normal and for pinpointing switch to Black sand mode and it is OK.
5. GB for disc is I suppose at this moment negative, nice negative.
My main interest is: DO YOU HAVE ANY info which trimmer is important for change factory preset mode from permanent POS (in disk mode) to NEG mode? I am looking for picture of control board and indexing right trimmer. It can be the same for all Freq?
So, do not hesitate support this discussion, and if we will have lucky, I will posted back result, be sure.
The best way how to explain it is asking WHY, you know.
Why I want to do it?
1. AD 180 can do more.
2. Too positive GB is good for disk stability, but reducing depth for small targets in disk mode.
3. I need any disk for iron as minimum only, disk circuit is very good, survive it and me too.
4. I need hear detector "tick tig ticky tig" - light noise during swimming - it is significant mark - this is a maximum of power, maximum of volume what I can get.
5. Better in depth is the same as better in small targets, is not it.
6. So, result what I called is raise a chance catch specific unclear noises small targets what are deeper than standard (POS/NEUTRAL/NEG- in acceptable level) set up Vaquero can do.
7. My experience is, if I use overloaded receiver and AD 180 (f.e. unstable set Tejon), no problem with AD 180. Tick tig ticky stopped and indexing beep is clear, strong and good.
8. Factory preset Vaquero is stable too much. It sitting down too conservative. I have no chance to do it what I want through negative AM GB only, at this moment it is wrong, to be too much negative in AM, due lost small targets, it is non-productive way.
Result is: I need light shift with Disk GB to NEG. It is all.
Reason is: I need IT.
Ufff, thank you, it was useful for me for fixing my thoughts and describing it, thanks again, .... schematic? Which trimmer need to be adjusted?
Regards
litrfree